PHREEQC Pond

NOTE: This feature is distributed with SysCAD but is currently in BETA. Please contact us ([email protected]) if you run into any issues using this model. This page is currently under development and details may change. Use with caution - we do not guarantee compatibility between different BETA versions.

Navigation: Models ➔ TCE Models ➔ PHREEQC ➔ PHREEQC Pond

PHREEQC Overview	PHREEQC Database Utility	PHREEQC Model Configuration	PHREEQC Direct Calc	PHREEQC Side Calc	PHREEQC Reactor	PHREEQC Evaporator	PHREEQC Flash Tank	PHREEQC Reverse Osmosis	PHREEQC Solvent Extraction	PHREEQC Feeder	PHREEQC Pond (Dynamic)	PHREEQC Tank (Dynamic)

Latest SysCAD Version: 25 October 2024 - SysCAD 9.3 Build 139.36522

Related Links: PHREEQC SysCAD Project Workflow

Released as a BETA version in Build 139.30599.

General Description

The PHREEQC Pond model is used in the Dynamic mode to emulate an Evaporation Pond. The user has the option to divide the pond into two layers, a bed where most of the solids settle and a clarified liquor layer for liquids, or consider the pond as a single layer. In any case, the concentration of the pore liquid in the bed layer and the concentration of the supernatant pond liquid is always equal and in equilibrium with the solids.

The PHREEQC Pond model allows the user to 'call' the PHREEQC solver to determine the state of a pond contents.

Notes

The user MUST have added and configured a PHREEQC Model Configuration unit in the SysCAD project before this unit can function.
Installation of PHREEQC is not required to use the PHREEQC functionality in SysCAD. If the user wishes to install PHREEQC, please see https://www.usgs.gov/software/PHREEQC-version-3 for more information.

Inputs and Outputs

Label	Required Optional	Input Output	Number of Connections		Description
Label	Required Optional	Input Output	Min	Max	Description
Feed	Required	In	1	10	The feed to the Pond.
Overflow	Required	Out	1	1	Pond overflow stream.
CL_Out	Optional	Out	0	1	Outlet stream from the Clarified Liquor layer.
Bed_Out	Optional	Out	0	1	Outlet stream from the Bed layer.
Seepage	Optional	Out	0	1	Pond seepage.
Vent	Optional	Out	0	1	Vent Stream (Vapour Only).

Model Theory

The PHREEQC Pond Model uses the PHREEQC algorithms and data to determine the status of the aqueous solution.

Mapping of the SysCAD to PHREEQC streams is done via Species Mapping.

The PHREEQC Pond can be incorporated into a SysCAD flowsheet, it can be connected with SysCAD inlet and outlet streams.

User connects the PHREEQC Pond with SysCAD input streams,
The SysCAD feed stream(s) using SysCAD species is converted into PHREEQC "Input" using PHREEQC Species. The species mapping is defined in the corresponding PHREEQC Model Configuration unit model.
The PHREEQC Pond calls the PHREEQC algorithms to determine the status of the mixture using the converted PHREEQC "input" data.
The PHREEQC results are displayed in the "output" tab using PHREEQC species.
- If the PHREEQC Pond is in Side Calc mode, the results are NOT converted into SysCAD species. (SysCAD stream outlet = sum of SysCAD inlet streams, no change will occur)
- If the PHREEQC Pond is in Reactor mode, then the results are converted back into SysCAD species. Please see Species Mapping for more information.

NOTES:

The Input, Output and Diff tab pages are displayed using PHREEQC species, as defined in the database (.dat) specified in the corresponding PHREEQC Model Configuration unit model.
The species used in the SysCAD project are shown on the optional Sp pages, shown as part of the QFeed, QBypass, QUnmapped, QRxnProdBypass and QProd pages.
The calculations performed are similar to using PHREEQC directly, except the contents of the SysCAD stream are mapped to equivalent PHREEQC species using the settings defined in the PHREEQC Model Configuration unit model. Please see https://www.usgs.gov/software/phreeqc-version-3 for more information.

Calculation of Osmotic Pressure

PHREEQC calculates the activity of water, which is then used to calculate the osmotic pressure by the Van't Hoff formula. The Van't Hoff formula is:

[math]\displaystyle{ \Pi=-\frac{RT}{\overline{V}}ln(a_w) }[/math]

where [math]\displaystyle{ \Pi }[/math] is the osmotic pressure, [math]\displaystyle{ \overline{V} }[/math] is the partial molar volume of water (ideal), and [math]\displaystyle{ a_w }[/math] is the activity of water (mole fraction basis).

Workflow

The suggested workflow for configuring the model is:

Make sure the project contains at least one of the PHREEQC Model Configuration model, and the model is loaded with the correct PHREEQC database you would like to use for the PHREEQC Pond model.
On the PHREEQCPond tab page, configure the model - methods, pressures, etc.
On the TCE tab page, select the correct ChemModel (to match step 1) (Note: In older builds, this selection was made on the PHREEQCPond tab page).
Select other TCE options (Bypass, CFE, etc.)
Perform an equilibrium calculation by pressing Solve in SysCAD.
The Results are displayed in the PHREEQCResults and Output tabs.
Check and fix any species mapping issues. (PHREEQC resulting species may change if the operating conditions change, so it is likely a change of temperature or feed composition will result in different PHREEQC species.)

Data Sections

PHREEQCPond tab - The first tab contains general information relating to the unit and allows the user to configure the unit.
Outlets tab - Optional tab, only visible if one of the optional slurry outlets are connected (CL_Out, Bed_Out or Seepage). This tab allows user to configure the various outputs from the pond as defined in the list of outputs above.
Results tab - Contains results of the model including summary of content parameters.
TCE tab - Optional tab, only visible if Rxns.Option = TCE. This tab allows the user to choose the corresponding PHREEQC Model Configuration unit and set other TCE options.
CFE - Optional tab, only visible if Rxns.Option = TCE and the UseCFE option is enabled on the TCE tab page.
Bypass - Optional tab, only visible if Rxns.Option = TCE and the WithBypass option is enabled on the TCE tab page.
RxnBypass - Optional tab, only visible if Rxns.Option = TCE and the WithBypass option is enabled on the TCE tab page.
PHREEQCResults tab - Optional tab, only visible if Rxns.Option = TCE. This tab displays the key results of the calculations.
Input tab - Optional tab, only visible if Rxns.Option = TCE. This tab displays a summary of the mapped Input stream as PHREEQC species.
Output tab - Optional tab, only visible if Rxns.Option = TCE. This tab displays the Output stream results including the amounts of each PHREEQC species present in the final mixture.
Diff tab - Optional tab, only visible if Rxns.Option = TCE and the ShowRxnDiff option is enabled on the TCE tab page. This tab displays the amounts of each species which are formed or reacted as part of the calculations.
Scaling tab - Optional tab, only visible if the ShowScaling option is enabled on the TCE tab.
ElemBal tab - Optional tab, only visible if Rxns.Option = TCE. This tab displays an elemental balance between the Input and Output streams.
PhDeport tab - Optional tab, only visible if Rxns.Option = TCE and the PhaseElemDeportment option is enabled on the TCE tab page. This tab shows the movement of elements for the Solid, Liquid and Gas phases.
IPhDeport tab - Optional tab, only visible if Rxns.Option = TCE and the IPhaseElemDeportment option is enabled on the TCE tab page. This tab shows the movement of elements for the individual PHREEQC phases.
QUnmapped - Optional tab, only visible if Rxns.Option = TCE and ShowQUnmapped is enabled on the TCE tab page.
QRxnUnmapped - Optional tab, only visible if Rxns.Option = TCE and ShowQRxnUnmapped is enabled on the TCE tab page.
QBypass - Optional tab, only visible if Rxns.Option = TCE and ShowQBypass is enabled on the TCE tab page.
QRxnBypass - Optional tab, only visible if Rxns.Option = TCE and ShowQRxnBypass is enabled on the TCE tab page.
CRB - Optional tab, only visible if Rxns.Option = CRB.
MU - Optional tab, or multiple tabs if more than 1 Makeup is selected. Only visible if one of more Makeups are enabled in the Evaluation Block on the first tab page.
QFeed - Optional tab, only visible if ShowQFeed is enabled on the first tab page. This page shows the properties of the mixed stream as the feed to the unit. If user has specified a required pressure in the unit, the mixed feed will be set to this pressure. This may cause the temperature of the mixture to change if the delta P is significantly different.
Bed tab - Optional tab, only visible if BedLayer.Partition and ShowBed are enabled on the first tab page. Contains data on the material in the bed.
Content tab - contains data on the material in the pond.
Preset tab - Optional tab, only visible if UsePreset option is enabled on the first tab page. Allows user to define the Preset composition.
QCL - Optional tab, only visible if the CL_Out outlet is connected and ShowQCL is enabled on the first tab page. This page shows the properties of the CL_Out stream.
QBed - Optional tab, only visible if the Bed_Out outlet is connected and ShowQBed is enabled on the first tab page. This page shows the properties of the Bed_Out stream.
Info tab - contains general settings for the unit and allows the user to include documentation about the unit and create Hyperlinks to external documents.
Links tab, contains a summary table for all the input and output streams.
Audit tab - contains summary information required for Mass and Energy balance. See Model Examples for enthalpy calculation Examples.

PHREEQCPond tab page

Unit Type: PHREEQCPond - The first tab page in the access window will have this name.

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
Tag	Display	This name tag may be modified with the change tag option.
Condition	Display	OK if no errors/warnings, otherwise lists errors/warnings.
ConditionCount	Display	The current number of errors/warnings. If condition is OK, returns 0.
GeneralDescription / GenDesc	Display	This is an automatically generated description for the unit. If the user has entered text in the 'EqpDesc' field on the Info tab (see below), this will be displayed here. If this field is blank, then SysCAD will display the UnitType or SubClass.
Requirements (Pond Size)
Capacity.Volume	Input	The volume of the pond.
Pond/Capacity.Area	Input	The surface area of the pond.
Pond/Capacity.Depth	Calc	The depth of the pond, calculated by Depth = Volume / Area.
Requirements
TemperatureReqd / T_Reqd	Input	The required temperature of the pond.
Rxns.Option	None	There are no reactions in the pond.
	TCE	PHREEQC calculations will be performed on the pond contents.
	CRB	The user can specify reactions to occur on the pond contents. If this is selected then the associated page, CRB becomes visible and may be configured. Note: The user does not have to configure a reaction file, even if this option is selected.
TCE_LiqBypassFrac	Input	Only visible if Rxns.Options = TCE. The fraction of the liquids that bypass the PHREEQC calculations.
TCE_SolBypassFrac	Input	Only visible if Rxns.Options = TCE. The fraction of the solids that bypass the PHREEQC calculations.
Rxns.LiqBypassFrac	Input	Only visible if Rxns.Options = CRB. The fraction of the liquids that bypass the reaction block.
Rxns.SolBypassFrac	Input	Only visible if Rxns.Options = CRB. The fraction of the solids that bypass the reaction block.
BedLayer.Partition	Tickbox	Separates the contents of the pond into two layers, Clarified Liquor and Bed. The Bed layer is the bottom layer.
BedLayer.FracOfSolids	Input	Only visible if BedLayer.Partition has been enabled. The fraction of the solids that report to the Bed layer.
BedLayer.LiquidFrac	Input	Only visible if BedLayer.Partition has been enabled. The fraction liquids in the Bed layer.
Requirements (Evaporation)
Evap.Method	None	There is no evaporation from the pond.
	Massflow	The user can specify the mass flow of water to be evaporated.
	Volumeflow	The user can specify the volume flow of water to be evaporated.
	Height Rate	The user can specify the rate of evaporation of water as a length per unit time. This will be multiplied by the surface area of the pond to obtain a volume of water to be evaporated.
Evap.QmReqd	Input	Only visible if Evap.Method = Massflow. The mass flow of water to be evaporated.
Evap.QvReqd	Input	Only visible if Evap.Method = Volumeflow. The volume flow of water to be evaporated.
Evap.RateReqd	Input	Only visible if Evap.Method = Height Rate. The required evaporation rate.
Evap.MinWaterFrac	Input	Visible if Evap.Method is any method other than None. The minimum fraction of water to be maintained in the pond. Evaporation may be less than specified to prevent the fraction of water being less than this value.
EB... (Evaluation Block)
EvalSequence	Calc	The sequence in which the sub models (which are part of the evaluation blocks) will be calculated. The sequence is determined by the priority selection for the individual sub-models. Note: If the user chooses On-AutoSequence then SysCAD will determine the sequence of the sub-models. The auto evaluation sequence followed will be the order the sub models are listed below.
Makeups	Input	The number of Makeup Blocks required. Extra dropdown options Makeup1, Makeup2, etc. will be added to allow these to be switched on and off and prioritised in relation to the other sub-models.
MakeupX	List	This can be used to switch the Makeup Block (MU) on or off and prioritise it in relation to the other sub-models. If this is 'On' then the associated page, MUX becomes visible and may be configured. Note: This field is only visible if the entry for 'Makeups' is greater than 0. If there is one makeup then X=1. If there are two makeups, then X=1 and X=2, etc.
PresetData...
UsePreset	Tickbox	If ticked, will allow user to set temperature, level and composition of the pond at startup. The composition can be set on the Preset tab page.
Temperature / T	Input	Only visible if UsePreset has been enabled. The temperature of the contents of the pond at startup.
Level	Input	Only visible if UsePreset has been enabled. The level of the pond at startup.
Options
TrackOverflow	Tickbox	If ticked, will enable warnings if material is sent to overflow stream.
ShowQFeed	Tickbox	Allows the user to view the QFeed and associated tab pages, showing the properties of the combined feed stream. See Material Flow Section. This will be prior to any sub-model actions, mixing with the pond content or PHREEQC calculations.
ShowBed	Tickbox	Only visible if BedLayer.Partition has been enabled. Allows the user to view the Bed and associated tab pages, showing the properties of the Bed layer. See Material Content Section.
ShowCL	Tickbox	Only visible if BedLayer.Partition has been enabled. Allows the user to view the CL and associated tab pages, showing the properties of the Clarified Liquor layer. See Material Content Section.
ShowQCL	Tickbox	Only visible if CL_Out outlet has been connected. Allows the user to view the QCL and associated tab pages, showing the properties of the Clarified Liquor outlet stream. See Material Flow Section.
ShowQBed	Tickbox	Only visible if Bed_Out outlet has been connected. Allows the user to view the QBed and associated tab pages, showing the properties of the Bed outlet stream. See Material Flow Section.

Outlets tab page

Notes:

All gases exit via the Gas Vent and cannot exit via normal Outlet links.
If no Gas Vent is connected, then any Gas will exit via an automatically created Gas Spill direct link.

Tag (Long/Short)	Input/ Calc	Description
(NOTE: Most fields will not be shown for a particular outlet if it is not connected)
*Requirements (Clarified Liquor Outlet)*
CL...
ConnectedPipe	Display	The tag of the connected pipe for the Clarified Liquor Outlet.
Order	Display	The order used for determining outlet flows.
Filter	None	All liquid and solid material will be able to exit via the connected pipe.
	Block-Solids	Solids will be not be allowed to exit via the connected pipe.
	Block-Liquids	Liquids will be not be allowed to exit via the connected pipe.
	Composition	Allows the user to specify the solid, liquid and vapour fractions.
	Individual Phase	Allows the user to specify an individual phase to draw from the pond.
Composition.SolidFrac / Sf	Input	Only visible if Filter = Composition. The required solid fraction of the stream.
Composition.LiquidFrac / Lf	Input	Only visible if Filter = Composition. The required liquid fraction of the stream.
Composition.VapourFrac / Vf	Input	Only visible if Filter = Composition. The required vapour fraction of the stream.
IPhase / IPh	Input	Only visible if Filter = Individual Phase. The required individual phase of the stream.
CL_Out...
Outlet XXX
These Output connection tags are also available on the Pipe access window. Any changes made here will be updated on the pipe access window and vice-versa.
CapacityControl	Off	The maximum mass flow through the outlet will be set to unlimited amount (uncontrolled).
	ByMassFlow	The user can specify the maximum mass flow through the outlet.
	ByVolumeFlow	The user can specify the maximum volumetric flow through the outlet.
Qm.ReqdCapacity / Qm.Capacity	Input	Visible with the ByMassFlow method. The required pipe Capacity in mass flow.
Qm.MinCapacity / Qm.MinCap	Input	Visible with the ByMassFlow method. The minimum user specified flow capacity by mass.
Qm.MaxCapacity / Qm.MaxCap	Input	Visible with the ByMassFlow method. The maximum user specified flow capacity by mass. Enter * for unlimited flow.
Qv.ReqdCapacity / Qv.Capacity	Input	Visible with the ByVolumeFlow method. The required pipe Capacity in volumetric flow.
Qv.MinCapacity / Qv.MinCap	Input	Visible with the ByVolumeFlow method. The minimum user specified flow capacity by volume.
Qv.MaxCapacity / Qv.MaxCap	Input	Visible with the ByVolumeFlow method. The maximum user specified flow capacity by volume. Enter * for unlimited flow.
MeasRho	Display	The stream density used when converting between mass and volume flows.
OverCapacity	Spill	If more material enters the pipe then the Maximum Capacity value, then the excess material will be 'spilled' and sent to the Spills area.
OverCapacity	Accept	If more material enters the pipe then the Maximum Capacity value, then the pipe must accept the excess material.
BatchMethod	None	The Batch functionality is not enabled.
	Total Mass	The Batch functionality is enabled and the required batch size is defined in terms of Mass flow. Further fields will become visible if this option is selected allowing the user to set the required batch mass.
	Total Volume	The Batch functionality is enabled and the required batch size is defined in terms of Volume flow. Further fields will become visible if this option is selected allowing the user to set the required batch volume.
The following fields will be visible if Total Mass is selected as the Batch method.
M.BatchAddition	Input	The Mass of the required Batch. This amount of material will be allowed to flow out of the pipe at the rate specified in Qm.Capacity or Qv.Capacity. When this value is set the amount of material will be added to the amount of material already in M.BatchRemaining (the field below), and then this field will revert to 0.
M.BatchRemaining	Calc / Input	The Mass of material currently in a Batch, i.e. the amount of material in a Batch that still has to flow through the pipe. Normally this value is initialised at the start of a run and then it is calculated by SysCAD from the amount required in M.BatchAddition and the amount already delivered by the batch. However, the user may set this value and hence override the calculated Batch amount at any stage. If the users sets this as Undefined (or '*') this is equivalent to any infinite Batch and therefore the flow through the pipe will not be restricted.
M.BatchTotal	Display	The Total Mass that has flowed through the pipe using the Batch addition method.
The following fields will be visible if Total Volume is selected as the Batch method.
V.BatchAddition	Input	The Volume of the required Batch. This amount of material will be allowed to flow out of the pipe at the rate specified in Qm.Capacity or Qv.Capacity. When this value is set the amount of material will be added to the amount of material already in V.BatchRemaining (the field below), and then this field will revert to 0.
V.BatchRemaining	Calc / Input	The Volume of material currently in a Batch, i.e. the amount of material in a Batch that still has to flow through the pipe. Normally this value is initialised at the start of a run and then it is calculated by SysCAD from the amount required in V.BatchAddition and the amount already delivered by the batch. However, the user may set this value and hence override the calculated Batch amount at any stage. If the users sets this as Undefined (or '*') this is equivalent to any infinite Batch and therefore the flow through the pipe will not be restricted.
V.BatchTotal	Display	The Total Volume that has flowed through the pipe using the Batch addition method.
The following fields will be visible if Total Mass or Total Volume is selected as the Batch method.
BatchState	None	No Batch mode has been set.
	Inactive	A Batch method has been selected, but the Batch is undefined.
	Busy	A Batch method has been selected, there is material remaining in the Batch, and hence there is flow in the pipe due to the Batch.
	Stop Flow	A Batch method has been selected, there is NO material remaining in the Batch, and hence there is no flow in the pipe, i.e. the Batch will prevent any flow in the pipe.
BatchClearOnEmpty	Tickbox	If enabled, any remaining batch amount will be cleared on Empty action command.
BatchUsePreset	Tickbox	This enables the use of Preset for the Batch amount.
M or V.BatchUsePreset	Input	The Mass or Volume of the Batch when the model is Preset. Refer to Actions Commands - Preset for more information.
*Requirements (Seepage Outlet)*
Seepage...
ConnectedPipe	Display	The tag of the connected pipe for the Seepage Outlet.
Order	Display	The order used for determining outlet flows.
Filter	None	All liquid and solid material will be able to exit via the connected pipe.
	Block-Solids	Solids will be not be allowed to exit via the connected pipe.
	Block-Liquids	Liquids will be not be allowed to exit via the connected pipe.
	Composition	Allows the user to specify the solid, liquid and vapour fractions.
	Individual Phase	Allows the user to specify an individual phase to draw from the pond.
Composition.SolidFrac / Sf	Input	Only visible if Filter = Composition. The required solid fraction of the stream.
Composition.LiquidFrac / Lf	Input	Only visible if Filter = Composition. The required liquid fraction of the stream.
Composition.VapourFrac / Vf	Input	Only visible if Filter = Composition. The required vapour fraction of the stream.
IPhase / IPh	Input	Only visible if Filter = Individual Phase. The required individual phase of the stream.
Seepage...
Outlet XXX
These Output connection tags are also available on the Pipe access window. Any changes made here will be updated on the pipe access window and vice-versa.
CapacityControl	Off	The maximum mass flow through the outlet will be set to unlimited amount (uncontrolled).
	ByMassFlow	The user can specify the maximum mass flow through the outlet.
	ByVolumeFlow	The user can specify the maximum volumetric flow through the outlet.
Qm.ReqdCapacity / Qm.Capacity	Input	Visible with the ByMassFlow method. The required pipe Capacity in mass flow.
Qm.MinCapacity / Qm.MinCap	Input	Visible with the ByMassFlow method. The minimum user specified flow capacity by mass.
Qm.MaxCapacity / Qm.MaxCap	Input	Visible with the ByMassFlow method. The maximum user specified flow capacity by mass. Enter * for unlimited flow.
Qv.ReqdCapacity / Qv.Capacity	Input	Visible with the ByVolumeFlow method. The required pipe Capacity in volumetric flow.
Qv.MinCapacity / Qv.MinCap	Input	Visible with the ByVolumeFlow method. The minimum user specified flow capacity by volume.
Qv.MaxCapacity / Qv.MaxCap	Input	Visible with the ByVolumeFlow method. The maximum user specified flow capacity by volume. Enter * for unlimited flow.
MeasRho	Display	The stream density used when converting between mass and volume flows.
OverCapacity	Spill	If more material enters the pipe then the Maximum Capacity value, then the excess material will be 'spilled' and sent to the Spills area.
OverCapacity	Accept	If more material enters the pipe then the Maximum Capacity value, then the pipe must accept the excess material.
BatchMethod	None	The Batch functionality is not enabled.
	Total Mass	The Batch functionality is enabled and the required batch size is defined in terms of Mass flow. Further fields will become visible if this option is selected allowing the user to set the required batch mass.
	Total Volume	The Batch functionality is enabled and the required batch size is defined in terms of Volume flow. Further fields will become visible if this option is selected allowing the user to set the required batch volume.
The following fields will be visible if Total Mass is selected as the Batch method.
M.BatchAddition	Input	The Mass of the required Batch. This amount of material will be allowed to flow out of the pipe at the rate specified in Qm.Capacity or Qv.Capacity. When this value is set the amount of material will be added to the amount of material already in M.BatchRemaining (the field below), and then this field will revert to 0.
M.BatchRemaining	Calc / Input	The Mass of material currently in a Batch, i.e. the amount of material in a Batch that still has to flow through the pipe. Normally this value is initialised at the start of a run and then it is calculated by SysCAD from the amount required in M.BatchAddition and the amount already delivered by the batch. However, the user may set this value and hence override the calculated Batch amount at any stage. If the users sets this as Undefined (or '*') this is equivalent to any infinite Batch and therefore the flow through the pipe will not be restricted.
M.BatchTotal	Display	The Total Mass that has flowed through the pipe using the Batch addition method.
The following fields will be visible if Total Volume is selected as the Batch method.
V.BatchAddition	Input	The Volume of the required Batch. This amount of material will be allowed to flow out of the pipe at the rate specified in Qm.Capacity or Qv.Capacity. When this value is set the amount of material will be added to the amount of material already in V.BatchRemaining (the field below), and then this field will revert to 0.
V.BatchRemaining	Calc / Input	The Volume of material currently in a Batch, i.e. the amount of material in a Batch that still has to flow through the pipe. Normally this value is initialised at the start of a run and then it is calculated by SysCAD from the amount required in V.BatchAddition and the amount already delivered by the batch. However, the user may set this value and hence override the calculated Batch amount at any stage. If the users sets this as Undefined (or '*') this is equivalent to any infinite Batch and therefore the flow through the pipe will not be restricted.
V.BatchTotal	Display	The Total Volume that has flowed through the pipe using the Batch addition method.
The following fields will be visible if Total Mass or Total Volume is selected as the Batch method.
BatchState	None	No Batch mode has been set.
	Inactive	A Batch method has been selected, but the Batch is undefined.
	Busy	A Batch method has been selected, there is material remaining in the Batch, and hence there is flow in the pipe due to the Batch.
	Stop Flow	A Batch method has been selected, there is NO material remaining in the Batch, and hence there is no flow in the pipe, i.e. the Batch will prevent any flow in the pipe.
BatchClearOnEmpty	Tickbox	If enabled, any remaining batch amount will be cleared on Empty action command.
BatchUsePreset	Tickbox	This enables the use of Preset for the Batch amount.
M or V.BatchUsePreset	Input	The Mass or Volume of the Batch when the model is Preset. Refer to Actions Commands - Preset for more information.
*Requirements (Bed Outlet)*
Bed...
ConnectedPipe	Display	The tag of the connected pipe for the Bed Outlet.
Order	Display	The order used for determining outlet flows.
Composition.SolidFrac / Sf	Input	The required solid fraction of the stream.
Composition.LiquidFrac / Lf	Input	The required liquid fraction of the stream.
Bed_Out...
Outlet XXX
These Output connection tags are also available on the Pipe access window. Any changes made here will be updated on the pipe access window and vice-versa.
CapacityControl	Off	The maximum mass flow through the outlet will be set to unlimited amount (uncontrolled).
	ByMassFlow	The user can specify the maximum mass flow through the outlet.
	ByVolumeFlow	The user can specify the maximum volumetric flow through the outlet.
Qm.ReqdCapacity / Qm.Capacity	Input	Visible with the ByMassFlow method. The required pipe Capacity in mass flow.
Qm.MinCapacity / Qm.MinCap	Input	Visible with the ByMassFlow method. The minimum user specified flow capacity by mass.
Qm.MaxCapacity / Qm.MaxCap	Input	Visible with the ByMassFlow method. The maximum user specified flow capacity by mass. Enter * for unlimited flow.
Qv.ReqdCapacity / Qv.Capacity	Input	Visible with the ByVolumeFlow method. The required pipe Capacity in volumetric flow.
Qv.MinCapacity / Qv.MinCap	Input	Visible with the ByVolumeFlow method. The minimum user specified flow capacity by volume.
Qv.MaxCapacity / Qv.MaxCap	Input	Visible with the ByVolumeFlow method. The maximum user specified flow capacity by volume. Enter * for unlimited flow.
MeasRho	Display	The stream density used when converting between mass and volume flows.
OverCapacity	Spill	If more material enters the pipe then the Maximum Capacity value, then the excess material will be 'spilled' and sent to the Spills area.
OverCapacity	Accept	If more material enters the pipe then the Maximum Capacity value, then the pipe must accept the excess material.
BatchMethod	None	The Batch functionality is not enabled.
	Total Mass	The Batch functionality is enabled and the required batch size is defined in terms of Mass flow. Further fields will become visible if this option is selected allowing the user to set the required batch mass.
	Total Volume	The Batch functionality is enabled and the required batch size is defined in terms of Volume flow. Further fields will become visible if this option is selected allowing the user to set the required batch volume.
The following fields will be visible if Total Mass is selected as the Batch method.
M.BatchAddition	Input	The Mass of the required Batch. This amount of material will be allowed to flow out of the pipe at the rate specified in Qm.Capacity or Qv.Capacity. When this value is set the amount of material will be added to the amount of material already in M.BatchRemaining (the field below), and then this field will revert to 0.
M.BatchRemaining	Calc / Input	The Mass of material currently in a Batch, i.e. the amount of material in a Batch that still has to flow through the pipe. Normally this value is initialised at the start of a run and then it is calculated by SysCAD from the amount required in M.BatchAddition and the amount already delivered by the batch. However, the user may set this value and hence override the calculated Batch amount at any stage. If the users sets this as Undefined (or '*') this is equivalent to any infinite Batch and therefore the flow through the pipe will not be restricted.
M.BatchTotal	Display	The Total Mass that has flowed through the pipe using the Batch addition method.
The following fields will be visible if Total Volume is selected as the Batch method.
V.BatchAddition	Input	The Volume of the required Batch. This amount of material will be allowed to flow out of the pipe at the rate specified in Qm.Capacity or Qv.Capacity. When this value is set the amount of material will be added to the amount of material already in V.BatchRemaining (the field below), and then this field will revert to 0.
V.BatchRemaining	Calc / Input	The Volume of material currently in a Batch, i.e. the amount of material in a Batch that still has to flow through the pipe. Normally this value is initialised at the start of a run and then it is calculated by SysCAD from the amount required in V.BatchAddition and the amount already delivered by the batch. However, the user may set this value and hence override the calculated Batch amount at any stage. If the users sets this as Undefined (or '*') this is equivalent to any infinite Batch and therefore the flow through the pipe will not be restricted.
V.BatchTotal	Display	The Total Volume that has flowed through the pipe using the Batch addition method.
The following fields will be visible if Total Mass or Total Volume is selected as the Batch method.
BatchState	None	No Batch mode has been set.
	Inactive	A Batch method has been selected, but the Batch is undefined.
	Busy	A Batch method has been selected, there is material remaining in the Batch, and hence there is flow in the pipe due to the Batch.
	Stop Flow	A Batch method has been selected, there is NO material remaining in the Batch, and hence there is no flow in the pipe, i.e. the Batch will prevent any flow in the pipe.
BatchClearOnEmpty	Tickbox	If enabled, any remaining batch amount will be cleared on Empty action command.
BatchUsePreset	Tickbox	This enables the use of Preset for the Batch amount.
M or V.BatchUsePreset	Input	The Mass or Volume of the Batch when the model is Preset. Refer to Actions Commands - Preset for more information.
CL Outlet Stream
CL...
CapControl.MassFlowReqd / QmReqd	Calc	The mass flow required in the pipe set by the capacity control.
Pull.MassFlowReqd / QmReqd	Calc
MassFlowReqd / QmReqd	Calc	The mass flow required in the pipe. Minimum of CapControl.MassFlowReqd and Pull.MassFlowReqd.
MassFlow / Qm	Calc	The actual mass flow in the pipe.
VolFlow / Qv	Calc	The actual volumetric flow in the pipe.
Seepage Outlet Stream
Seepage...
CapControl.MassFlowReqd / QmReqd	Calc	The mass flow required in the pipe set by the capacity control.
Pull.MassFlowReqd / QmReqd	Calc
MassFlowReqd / QmReqd	Calc	The mass flow required in the pipe. Minimum of CapControl.MassFlowReqd and Pull.MassFlowReqd.
MassFlow / Qm	Calc	The actual mass flow in the pipe.
VolFlow / Qv	Calc	The actual volumetric flow in the pipe.
Bed Outlet Stream
Bed...
CapControl.MassFlowReqd / QmReqd	Calc	The mass flow required in the pipe set by the capacity control.
Pull.MassFlowReqd / QmReqd	Calc
MassFlowReqd / QmReqd	Calc	The mass flow required in the pipe. Minimum of CapControl.MassFlowReqd and Pull.MassFlowReqd.
MassFlow / Qm	Calc	The actual mass flow in the pipe.
VolFlow / Qv	Calc	The actual volumetric flow in the pipe.

Results tab page

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
Results Summary (Pond Contents)
Temperature / T	Calc	The current temperature of the contents of the pond.
Density / Rho	Calc	The current density of the contents of the pond.
TotalVol / Vt	Calc	The current volume of the contents of the pond.
Level / Lvl	Calc	The current level of the contents of the pond.
SolidFrac / Sf	Calc	The current fraction of solids in the contents of the pond.
TotalMass / Mt	Calc	The current mass of the contents of the pond.
InitTtlMass / InitMt	Calc	The mass of the contents of the pond at the start of the solver run.
DeltaTtlMass / DeltaMt	Calc	The total change in mass of the contents of the pond since the start of the solver run (TotalMass - InitTtlMass).
MassRateOfChange / QmAcc	Calc	The rate of accumulation of mass in the content of the pond.
MtAcc	Calc	The total change of mass over the time step.
Content.HeatFlow	Calc
Results Summary (Bed Layer) (This section is only visible if BedLayer.Partition has been enabled.)
BedLayer.TotalMass / Mt	Calc	The current mass of the contents of the bed layer.
BedLayer.TotalVol / Vt	Calc	The current volume of the contents of the bed layer.
BedLayer.Level / Lvl	Calc	The current level of the bed layer.
BedLayer.SolidFrac / Sf	Calc	The current fraction of solids in the bed layer.
BedLayer.ContentFrac	Calc	The fraction by volume of the bed layer compared to the total volume of the contents of the pond (BedLayer.TotalVol / TotalVol).
BedLayer.HeatFlow	Calc	The current level of the bed layer.
Results Summary (CL) (This section is only visible if BedLayer.Partition has been enabled.)
CL.TotalMass / Mt	Calc	The current mass of the contents of the clarified liquor layer.
CL.TotalVol / Vt	Calc	The current volume of the contents of the clarified liquor layer.
CL.SolidFrac / Sf	Calc	The current fraction of solids in the clarified liquor layer.
CL.ContentFrac	Calc	The fraction by volume of the clarified liquor layer compared to the total volume of the contents of the pond (CL.TotalVol / TotalVol).
Results Summary (Evaporation)
Evap.MassFlow / Qm	Calc	The mass flow of water evaporated.
Evap.VolumeFlow / Qv	Calc	The volume flow of water evaporated.
Evap.Rate	Calc	The evaporation rate.
Evap.HeatFlow	Calc	The energy (heat) required for evaporation of water.
Results Summary (TCE) (This section is only visible if Rxns.Options = TCE.)
TCE.Mt	Calc
TCE.HeatFlow	Calc
Bypass.Mt	Calc
Bypass.HeatFlow	Calc
Results Summary (CRB) (This section is only visible if Rxns.Options = CRB.)
Rxns.Mt	Calc
Rxns.HeatFlow	Calc
Bypass.Mt	Calc
Bypass.HeatFlow	Calc
Results Summary (Streams)
Feed.MassFlow / Qm	Calc	The feed mass flow to the pond.
MassRateOfChange / QmAcc	Calc	The rate of accumulation of mass in the content of the pond.
CL.MassFlow / Qm	Calc	Visible if CL_Out stream is connected. The mass flow of the Clarified Liquor (CL_Out) stream.
Seepage.MassFlow / Qm	Calc	Visible if Seepage stream is connected. The mass flow of the Seepage stream.
Bed.MassFlow / Qm	Calc	Visible if Bed_Out stream is connected. The mass flow of the Bed outlet (Bed_Out) stream.
Overflow.MassFlow / Qm	Calc	The mass flow of the overflow stream.
Vent.MassFlow / Qm	Calc	The mass flow of the vent stream.
HeatFlows
Content.HeatFlow	Calc
BedLayer.HeatFlow	Calc	Only visible if BedLayer.Partition has been enabled.
Evap.HeatFlow	Calc	The energy (heat) required for evaporation of water.
Bypass.HeatFlow	Calc
TCE.HeatFlow	Calc	Only visible if Rxns.Options = TCE.
Rxns.HeatFlow	Calc	Only visible if Rxns.Options = CRB.
HeatFlow	Calc	The sum of all heat flows.

TCE tab page

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
This program contains PHREEQC Copyright U.S. Geological Survey (USGS)
Chemistry Model
ChemModel...
UnitTag	List	The tag of the relevant PHREEQC Model Configuration unit model- this may be chosen from the drop down list of all PHREEQC Model Configuration unit models available in the project.
ModelCfgTagUsed/ModelCfgTag	Display	The tag of the relevant PHREEQC Model Configuration unit model.
Check		If the user clicks on this button, SysCAD will check that the UnitTag is a valid PHREEQC Model Configuration unit model.
ConnOK	Tickbox	If SysCAD finds a valid PHREEQC Model Configuration unit model, then this field will be enabled.
Status	OK	The specified chemistry model (PHREEQC Model Configuration) has been initialised correctly and the database file has been found and loaded correctly.
	ChemModel Tag not Specified	No tag has been specified for the Chemistry Model. Specify the desired Chemistry Model (PHREEQC Model Configuration) in the UnitTag field.
	Valid ChemModel Tag Required	The tag specified for the Chemistry Model in the UnitTag field is invalid and needs to be corrected.
	Init Required	The specified Chemistry Model (PHREEQC Model Configuration) needs to be initialised.
	ChemModel Load Required	The database of the specified Chemistry Model (PHREEQC Model Configuration) needs to be loaded.
	DLL or Version Error	There is a problem with the PHREEQC DLL or version.
	Init Failed	Initialisation of the specified Chemistry Model (PHREEQC Model Configuration) has been attempted but failed.
Select actions if species unmapped
FwdSpMap.UnmappedAction	Stop Solver	Any unmapped SysCAD species will cause the solver to stop, user will need to fix the species mapping before solving again.
FwdSpMap.UnmappedAction	Bypass	Any unmapped SysCAD species will be bypassed, i.e. will not be present in the PHREEQC input
RevSpMap.UnmappedAction	Make Inactive	Any unmapped SysCAD species will cause the model to be inactive.
	Stop Solver	Any unmapped SysCAD species will cause the solver to stop, user will need to fix the species mapping before solving again.
	Allow Solve	Any unmapped SysCAD species will be ignored. Model will solve but will have a mass balance error.
ActionOnError	Continue	The model will continue solving if the PHREEQC calculation fails.
	Pause	The model will pause solving if the PHREEQC calculation fails.
	Stop	The model will stop solving if the PHREEQC calculation fails.
Requirements
VLEModel	Display	Displays the VLE model used.
WithBypass	Tickbox	If this is ticked, then the Bypass tab page will appear.
Select dependent variable and target value
OpMode...
Target calculation details (only displayed if OpMode ≠ Temperature or FeedT)
TargCalc...
UseRelaxation	Tickbox
RelaxationFactor	Input	The RelaxationFactor, used when UseRelaxation is ticked. Values limits: 0.001 < RelaxationFactor < 5.
Settings		If the user clicks on this button, the all the target solver settings will be reset to their default values.
SpMoleFlow / QMl	Display	Only shown if AdjustVar.Method = AdjustQMl. The actual mole flow used of the adjusted species.
SpMoleFlow / Qm	Display	Only shown if AdjustVar.Method = AdjustQMl. The actual mass flow used of the adjusted species.
PHREEQC Environmental Heat Transfer
PHREEQC.HeatLossMethod	None	No heat transfer between the unit and the environment.
	Fixed HeatFlow	The user specifies a fixed heat loss between the unit and the environment.
	Ambient	SysCAD calculates the overall heat loss based on user specified HTC and Area and the temperature difference between the Feed and environmental temperatures. The environmental temperature is assumed to remain constant.
PHREEQC.EHX.HeatLossReqd	Input	Visible when the HeatLossMethod = Fixed HeatFlow. The required heat loss.
PHREEQC.EHX.HTC	Input	Visible when the HeatLossMethod = Ambient. The Overall Heat Transfer coefficient.
PHREEQC.EHX.Area	Input	Visible when the HeatLossMethod = Ambient. The Heat Transfer area.
PHREEQC.EHX.AmbientT	Display	Visible when the HeatLossMethod = Ambient. The ambient temperature. The ambient temperature is specified in the Plant Model - Environment_Tab
PHREEQC.EHX.HeatLoss	Calc	Visible when the HeatLossMethod = Ambient. The calculated heat flowrate.
Options
ShowQUnmapped	Tickbox	Allows the user to view the QUnmapped and associated tab pages. See Material Flow Section. This is the SysCAD species flows which are not mapped to PHREEQC species, and therefore are not taken into account in the PHREEQC calculation.
ShowQRxnUnmapped	Tickbox	Allows the user to view the QRExnUnmapped and associated tab pages. See Material Flow Section.
ShowQBypass	Tickbox	Only visible when WithBypass is ticked. Allows the user to view the QBypass and associated tab pages. See Material Flow Section. This is the SysCAD species flows which bypass the PHREEQC calculation.
ShowQRxnBypass	Tickbox	Only visible when WithBypass is ticked. Allows the user to view the QRxnBypass and associated tab pages. See Material Flow Section.
ShowRxnDiff	Tickbox	Allows the user to view the Diff tab page. This shows the difference between the mapped input stream seen by PHREEQC and the PHREEQC calculation results.
ShowScaling	Tickbox	Available from Build 139.34985. Allows the user to view the Scaling tab page.
PhaseElemDeportment	Tickbox	If this is ticked, then the PhDeport tab page will appear. This tab shows the mass movement of elements for the Solid, Liquid and Gas phases.
IPhaseElemDeportment	Tickbox	If this is ticked, then the IPhDeport tab page will appear. This shows how the elements move between phases due to the PHREEQC calculation results.
ShowPlotter	Tickbox	This option is only visible if this model has been successfully run. Allows the user to perform a parameter sweep using the product stream of the side calculator. If this is ticked, then the ParamSweep tab page will appear.
PHREEQCInput		When this button is pressed, user can select to copy the Feed or Product information to clipboard.

CFE tab page

This tab is only visible if the UseCFE option is enabled on the TCE tab page.

This option allows a portion of a species to be locked up and not allowed to react.
Applying CFE can have a significant effect on the final composition, use of this feature requires detailed knowledge of the process chemistry.
This feature is unavailable if using SysCAD VLE with PHREEQC.

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
Constrained Free Energy (CFE) Configuration
CFE...
SpeciesName		The Species:Long or Short button is used to change the display of the Species names between the Short form, the Chemical compound, or the longer species names.
Filter View
Filter		This button will enable or disable the species filter options.
ShowUnmapped (Only visible if Filter is enabled)	Tickbox	When enabled, all species will be displayed. When disabled, only species that are mapped to a SysCAD species will be shown.
Phases (Only visible if Filter is enabled)	All	No filtering of species based on phase.
	Solids	Only show solid phase species, hide other species.
	Liquids	Only show liquid phase species, hide other species.
	Vapours	Only show vapour (gaseous) phase species, hide other species.
	Solids & Liquids	Only show solid and liquid phase species, hide other species.
	Solids & Vapours	Only show solid and vapour (gaseous) phase species, hide other species.
	Liquids & Vapours	Only show liquid and vapour (gaseous) phase species, hide other species.
	IPhase	Only show "IPhase" individual phase species, hide other species. The individual phases shown will depend on the PHREEQC database chosen.
Filters	Display	Always set to 'Content'.
Content (Only visible if Filter is enabled)	All	No filtering of species based on element or name.
	Contains Any Element	This will display all species that contain any of the elements entered in their elemental definition.
	Contains All Elements	This will display only species that contain ALL of the elements entered in their elemental definition.
	Starts with ...	This will display species that start with the text entered based on the short or long species tag depending on the current SpeciesTag selection.
	Contains any ...	This will display species that contain the text entered in the currently displayed short or long species tag.
	Contains All ...	This will display species that contain ALL the separate text entered in the currently displayed short or long species tag.
Select	Input	Only visible if Filter is enabled and Content is NOT set to All. The user specified Elements or text to filter the species list. Refer to Species Filter for more information and examples.
(The following tables (one per phase) display the PHREEQC species from the selected database. The user can set the Inert Fraction for each species. Note that liquid ions are not shown on this page as the Inert Fractions cannot be set for them.) (Each table has the following column (one row per PHREEQC species):)
InertFrac	Input	The user specified fraction of the species that is considered inert, i.e. cannot react to form other species/ions. The presence of the inert fraction is still taken into account when calculating stream properties. This is only available as an input for molecular species (not ions).

Bypass tab page

This tab is only visible if the WithBypass option is enabled on the TCE tab page. This will allow some or all of the SysCAD species to bypass the thermodynamic engine calculations.

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
Specify Bypass of Feed
BypassMode	Species	A bypass fraction can be set for each species in the project.
BypassMode	Phases	A bypass fraction can be set for each phase (Solid, Liquid or Vapour) in the project.
BypassUnmapped		If this button is pressed then the bypass fraction for all Unmapped Species will be set to 100%. This is only relevant if BypassMode = Species. NOTE: There is no automatic undo for this function. It is recommended to bypass all species in the SysCAD model which are not present in the PHREEQC model you are using.
ShowUnmappedSpecies	Tickbox	If ticked, all the unmapped species will be displayed in a list immediately under this field.
BypassSpCount	Calc	The number of species to be bypassed.
PhaseBypass... (only displayed if BypassMode = Phases)
PhaseBypass.Solid.MF	Input	Only displayed if BypassMode = Phases. The user specified Bypass fraction for all SysCAD solid species. A non-zero value will allow some or all (100%) of the SysCAD solid species to bypass the thermodynamic engine calculations.
PhaseBypass.Liquid.MF	Input	Only displayed if BypassMode = Phases. The user specified Bypass fraction for all SysCAD liquid species. A non-zero value will allow some or all (100%) of the SysCAD liquid species to bypass the thermodynamic engine calculations.
PhaseBypass.Vapour.MF	Input	Only displayed if BypassMode = Phases. The user specified Bypass fraction for all SysCAD vapour species. A non-zero value will allow some or all (100%) of the SysCAD vapour species to bypass the thermodynamic engine calculations.
The remaining fields are only displayed if BypassMode = Species)
On		This button will enable or disable the species filter options.
Phases (Only visible if Filter is enabled)	All	No filtering of species based on phase.
	Solids	Only show solid phase species, hide other species.
	Liquids	Only show liquid phase species, hide other species.
	Vapours	Only show vapour (gaseous) phase species, hide other species.
	Solids & Liquids	Only show solid and liquid phase species, hide other species.
	Solids & Vapours	Only show solid and vapour (gaseous) phase species, hide other species.
	Liquids & Vapours	Only show liquid and vapour (gaseous) phase species, hide other species.
	IPhase	Only show "IPhase" individual phase species, hide other species. The individual phases shown will depend on the PHREEQC database chosen.
Filters	Display	Always set to 'Content'.
Content (Only visible if Filter is enabled)	All	No filtering of species based on element or name.
	Contains Any Element	This will display all species that contain any of the elements entered in their elemental definition.
	Contains All Elements	This will display only species that contain ALL of the elements entered in their elemental definition.
	Starts with ...	This will display species that start with the text entered based on the short or long species tag depending on the current SpeciesTag selection.
	Contains any ...	This will display species that contain the text entered in the currently displayed short or long species tag.
	Contains All ...	This will display species that contain ALL the separate text entered in the currently displayed short or long species tag.
Select	Input	Only visible if Filter is enabled and Content is NOT set to All. The user specified Elements or text to filter the species list. Refer to Species Filter for more information and examples.
GroupValue	Input	The user specified bypass value that will be used for all species displayed when the Set to GroupValue button is pressed.
SetVisible		When pressed, this button will set the bypass parameter for all species currently displayed (based on Filter settings) equal to the GroupValue.
SysCAD Feed Stream Bypass
(The following table displays all the SysCAD species in the project (unless restricted by the Filter settings). The table has the following column (one row per SysCAD species):)
Bypass.XXX	Input	The user specified Bypass fraction for SysCAD species XXX. A non-zero value will allow some or all (100%) of the SysCAD species to bypass the thermodynamic engine calculations.

RxnBypass tab page

This tab is only visible if the WithBypass option is enabled on the TCE tab page. This will allow some or all of the SysCAD species to bypass the thermodynamic engine calculations.

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
Specify Bypass during Solver Solution
RxnBypass...
BypassMode	Species	A bypass fraction can be set for each species in the project.
BypassMode	Phases	A bypass fraction can be set for each phase (Solid, Liquid or Vapour) in the project.
BypassUnmapped		If this button is pressed then the bypass fraction for all Unmapped Species will be set to 100%. This is only relevant if BypassMode = Species. NOTE: There is no automatic undo for this function. It is recommended to bypass all species in the SysCAD model which are not present in the PHREEQC model you are using.
ShowUnmappedSpecies	Tickbox	If ticked, all the unmapped species will be displayed in a list immediately under this field.
BypassSpCount	Calc	The number of species to be bypassed.
PhaseBypass... (only displayed if BypassMode = Phases)
PhaseBypass.Solid.MF	Input	Only displayed if BypassMode = Phases. The user specified Bypass fraction for all SysCAD solid species. A non-zero value will allow some or all (100%) of the SysCAD solid species to bypass the thermodynamic engine calculations.
PhaseBypass.Liquid.MF	Input	Only displayed if BypassMode = Phases. The user specified Bypass fraction for all SysCAD liquid species. A non-zero value will allow some or all (100%) of the SysCAD liquid species to bypass the thermodynamic engine calculations.
PhaseBypass.Vapour.MF	Input	Only displayed if BypassMode = Phases. The user specified Bypass fraction for all SysCAD vapour species. A non-zero value will allow some or all (100%) of the SysCAD vapour species to bypass the thermodynamic engine calculations.
The remaining fields are only displayed if BypassMode = Species)
On		This button will enable or disable the species filter options.
Phases (Only visible if Filter is enabled)	All	No filtering of species based on phase.
	Solids	Only show solid phase species, hide other species.
	Liquids	Only show liquid phase species, hide other species.
	Vapours	Only show vapour (gaseous) phase species, hide other species.
	Solids & Liquids	Only show solid and liquid phase species, hide other species.
	Solids & Vapours	Only show solid and vapour (gaseous) phase species, hide other species.
	Liquids & Vapours	Only show liquid and vapour (gaseous) phase species, hide other species.
	IPhase	Only show "IPhase" individual phase species, hide other species. The individual phases shown will depend on the PHREEQC database chosen.
Filters	Display	Always set to 'Content'.
Content (Only visible if Filter is enabled)	All	No filtering of species based on element or name.
	Contains Any Element	This will display all species that contain any of the elements entered in their elemental definition.
	Contains All Elements	This will display only species that contain ALL of the elements entered in their elemental definition.
	Starts with ...	This will display species that start with the text entered based on the short or long species tag depending on the current SpeciesTag selection.
	Contains any ...	This will display species that contain the text entered in the currently displayed short or long species tag.
	Contains All ...	This will display species that contain ALL the separate text entered in the currently displayed short or long species tag.
Select	Input	Only visible if Filter is enabled and Content is NOT set to All. The user specified Elements or text to filter the species list. Refer to Species Filter for more information and examples.
GroupValue	Input	The user specified bypass value that will be used for all species displayed when the Set to GroupValue button is pressed.
SetVisible		When pressed, this button will set the bypass parameter for all species currently displayed (based on Filter settings) equal to the GroupValue.
SysCAD Feed Stream Bypass
(The following table displays all the SysCAD species in the project (unless restricted by the Filter settings). The table has the following column (one row per SysCAD species):)
Bypass.XXX	Input	The user specified Bypass fraction for SysCAD species XXX. A non-zero value will allow some or all (100%) of the SysCAD species to bypass the thermodynamic engine calculations.

PHREEQCResults tab page

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
PHREEQC Calculation Results Summary
Feed Mass Summary
Bypass.Mass / M	Display	The mass of material in the feed which bypasses the calculation due to user selection of bypass species. Use ShowQBypass to view full stream.
Unmapped.Mass / M	Display	The mass of material in the feed which is not forward mapped to a species and therefore bypasses the calculation. Use ShowQUnmapped to view full stream.
PHREEQC.Feed.Mass / M	Display	The mass of material in the feed to the PHREEQC calculation.
TotalFeed.Mass / M	Display	The total feed mass to the PHREEQC model block. Sum of bypasses and feed to PHREEQC calculation.
Product Mass Summary
PHREEQC.Prod.Mass / M	Display	The mass flow of material in the product of the PHREEQC calculation. Same value as tag Prod.Qm.
RxnBypass.Mass / M	Display
RxnUnmapped.Mass / M	Display	The mass of material in the product which is not reverse mapped to SysCAD species.
TotalProd.Mass / M	Display	The total product mass for the PHREEQC model block. Sum of bypasses and product of PHREEQC calculation.
Solids Yield
Solids.Yield	Display	The solids concentration in the product stream.
Solids.Precip	Display	The change in solids flow, feed-product. A positive value indicates precipitation has occurred. A negative value indicates dissolution has occurred.
Content Properties Summary
Prod...
Temperature / T	Display	The Temperature of the final solution.
Pressure / P	Display	The Pressure of the final solution.
Mass / M	Display	The Mass of the final solution.
Hf@T	Display	The Enthalpy of the final solution per unit mass.
Enthalpy / totHf@T	Display	The Enthalpy of the final solution.
AqDensity / AqRho	Display	The density of aqueous species (solution) in the final solution.
Density / Rho	Display	The density of the final solution.
IonicStrength / I	Display	The molar Ionic Strength of the final solution.
pH	Display	The pH of the final solution.
Alkalinity	Display	The alkalinity of the final solution.
WaterActivity	Display	The water activity of the final solution.
TotalDissolvedSolids / TDS	Display	The mass concentration of Total Dissolved Solids (total aqueous-water) in the final solution.
OsmoticPressure / OsmP	Display	The Osmotic Pressure of the final solution.
ORP	Display	Available from Build 139.33865. The oxidation reduction potential (ORP) of the final solution referenced to the standard hydrogen electrode (SHE). This is also known as [math]\displaystyle{ E_h }[/math].
pKw	Display	The pKw of the final solution.
PHREEQCInput		When this button is pressed the Product information will be copied to the clipboard.
Zeros		If the Hide Zeros button is clicked, all phases/species that have NO mass flow will be hidden. If the Show Zeros button is clicked, all phases/species will be displayed, including those with zero mass flow. Note this setting applies to the subsequent pages as well.
Feed...
Feed Phase Content Summary
(The following table displays a summary of results for the different phases. The table has the following columns (one row per phase)):
Mass / M	Display	The mass of the relevant phase in the feed.
MassFrac / Mf	Display	The mass fraction of the relevant phase in the feed.
Moles / Ml	Display	The moles of the relevant phase in the feed.
MoleFrac / Mlf	Display	The mole fraction of the relevant phase in the feed.
Prod...
Prod Phase Content Summary
(The following table displays a summary of results for the different phases. The table has the following columns (one row per phase)):
Mass / M	Display	The mass of the relevant phase in the final solution.
MassFrac / Mf	Display	The mass fraction of the relevant phase in the final solution.
Moles / Ml	Display	The moles of the relevant phase in the final solution.
MoleFrac / Mlf	Display	The mole fraction of the relevant phase in the final solution.
PHREEQC Energy Balance
PHREEQC.HeatFlow	Display	Difference in enthalpy between the product and feed of the PHREEQC reactions calculated by SysCAD.
Bypass.HeatFlow	Display	The heat required to adjust the temperature and pressure of the bypass stream to exit conditions.
HeatLoss	Display	The environmental heat loss.
HeatFlow	Display	The heat flow required to achieve the product conditions relative to the feed conditions. Includes environmental heat loss if applicable. This is calculated by SysCAD and accounts for bypass and heat loss. Note that Bypass heat is calculated by SysCAD.
Forward Mapping Summary
FwdMap.ScdFeed	Display	This displays mass and SysCAD enthalpy of the feed stream to PHREEQC before mapping and after bypass and unmapped are removed.
FwdMap	Display	This displays mass and PHREEQC enthalpy of the Input stream to PHREEQC after forward mapping. The enthalpy of the FwdMap stream and the FwdMap.ScdFeed stream should be identical because the SysCAD-PHREEQC interface uses the SysCAD enthalpy model to calculate enthalpy
FwdMap.Diff	Display	This displays the difference in mass and enthalpy between the feed stream and Input stream. There should never be differences in mass. Small enthalpy differences are expected but large differences may indicate issues with SysCAD database enthalpy data.
FwdMap.RelDiff	Display	This displays the relative difference in mass and enthalpy between the feed stream and Input stream. There should never be differences in mass. Small enthalpy differences are expected but large differences may indicate issues with SysCAD database enthalpy data.
Reverse Mapping Summary
RevMap.TCEProd	Display	This displays mass and PHREEQC enthalpy of the Output stream from PHREEQC. The enthalpy of the RevMap.TCEProd stream and the RevMap stream should be identical because the SysCAD-PHREEQC interface uses the SysCAD enthalpy model to calculate enthalpy
RevMap	Display	This displays mass and SysCAD enthalpy of the Prod stream after reverse mapping.
RevMap.Diff	Display	This displays the difference in mass and enthalpy between the Output stream and Prod stream. There should never be differences in mass. Small enthalpy differences are expected but large differences may indicate issues with SysCAD database enthalpy data.
RevMap.RelDiff	Display	This displays the relative difference in mass and enthalpy between the Output stream and Prod stream. There should never be differences in mass. Small enthalpy differences are expected but large differences may indicate issues with SysCAD database enthalpy data.
Copy Reverse Mapping Reactions to Clipboard
RevMap.IonRxns		Pushing this button copies to the clipboard a list of reactions that were executed to perform the reverse mapping. These can then be pasted into Excel to generate a table.
Calculation Summary
Summary...
LastCalcType	Display	This displays the type of calculation (OpMode) used for the last calculation.
Remove		If the user clicks on this button, SysCAD will remove duplicate error messages received.
ErrorCount	Display	The total number of errors encountered in the last calculation.
ErrorXX	Display	If there are error messages associated with the last calculation, they will be displayed here.
ConvergenceError	Display	The largest numerical convergence error. This is often zero when the solution converges with no errors.

Input tab page

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
Content Properties Summary
Feed...
Temperature / T	Display	The Temperature of the feed solution. This is calculated using the SysCAD enthalpy context.
Pressure / P	Display	The Pressure of the feed solution.
Mass / M	Display	The Mass of the feed solution.
Hf@T	Display	The Enthalpy of the feed solution per unit mass. This is calculated by PHREEQC.
Enthalpy / totHf@T	Display	The Enthalpy of the feed solution. This is calculated by PHREEQC.
PHREEQCInput		When this button is pressed the Feed information will be copied to the clipboard.
Feed...
SpeciesName		The Species:Long or Short button is used to change the display of the Species names between the Short form, the Chemical compound, or the longer species names.
Zeros		If the Hide Zeros button is clicked, all species that have NO mass flow will be hidden. If the Show Zeros button is clicked, all species will be displayed, including those with zero mass flow.
StreamView		If the Mass button is clicked, the species will be shown in mass flow view. If the Mole button is clicked, the species will be shown in mole flow view.
Stream	Mass	Copy stream contents to clipboard, mass basis, for pasting into Excel. If Zeros is set to hide, zero values will not be copied to the clipboard.
	Mole	Copy stream contents to clipboard, mole basis, for pasting into Excel. If Zeros is set to hide, zero values will not be copied to the clipboard.
	Unmapped Mass	Copy unmapped stream contents to clipboard, mass basis, for pasting into Excel. If Zeros is set to hide, zero values will not be copied to the clipboard. Unmapped species are those which will not be mapped to the exiting SysCAD stream.
	Unmapped Mole	Copy unmapped stream contents to clipboard, mole basis, for pasting into Excel. If Zeros is set to hide, zero values will not be copied to the clipboard. Unmapped species are those which will not be mapped to the exiting SysCAD stream.
(The following tables display the mass/moles, mass/mole fraction of the individual species.) (Each table (one for each phase) has the following columns (one row for each species):)
Mass / M	Display	Visible when StreamView = Mass. The mass of the species in the feed stream.
MassFrac / Mf	Display	Visible when StreamView = Mass. The mass fraction of the species in the feed stream.
PhaseMassFrac / IPh:Mf	Display	Visible when StreamView = Mass. The mass fraction of the species in the displayed phase.
Moles / Ml	Display	Visible when StreamView = Mole. The moles of the species in the feed stream.
MoleFrac / Mlf	Display	Visible when StreamView = Mole. The mole fraction of the species in the feed stream.
PhaseMoleFrac / IPh:Mlf	Display	Visible when StreamView = Mole. The mole fraction of the species in the displayed phase.

Output tab page

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
Content Properties Summary
Prod...
Temperature / T	Display	The Temperature of the product solution. This is calculated by SysCAD enthalpy context.
Pressure / P	Display	The Pressure of the product solution.
Mass / M	Display	The Mass of the product solution.
Hf@T	Display	The Enthalpy of the product solution per unit mass. This is calculated by PHREEQC.
Enthalpy / totHf@T	Display	The Enthalpy of the product solution. This is calculated by PHREEQC.
AqDensity / AqRho	Display	The density of aqueous species (solution) in the final solution.
IonicStrength / I	Display	The molal Ionic Strength of the final solution, based on the molality (moles/mass of H2O) and charge of the individual ions.
pH	Display	The pH of the final solution.
Alkalinity	Display	The alkalinity of the final solution.
WaterActivity	Display	The water activity of the final solution.
TotalDissolvedSolids / TDS	Display	The mass concentration of Total Dissolved Solids (total aqueous-water) in the final solution.
OsmoticPressure / OsmP	Display	The Osmotic Pressure of the final solution. Please refer to Model Theory - Calculation of Osmotic Pressure for more information.
pKw	Display	The pKw of the final solution.
PHREEQCInput		When this button is pressed the Product information will be copied to the clipboard.
Copy Reverse Mapping Reactions to Clipboard
RevMap.IonRxns		A table of Ion Rebuild Reactions (ions->species) and their extents will be copied to the clipboard.
Prod...
SpeciesName		The Species:Long or Short button is used to change the display of the Species names between the Short form, the Chemical compound, or the longer species names.
Zeros		If the Hide Zeros button is clicked, all species that have NO mass flow will be hidden. If the Show Zeros button is clicked, all species will be displayed, including those with zero mass flow.
StreamView		If the Mass button is clicked, the species will be shown in mass flow view. If the Mole button is clicked, the species will be shown in mole flow view.
Stream	Mass	Copy stream contents to clipboard, mass basis, for pasting into Excel. If Zeros is set to hide, zero values will not be copied to the clipboard.
	Mole	Copy stream contents to clipboard, mole basis, for pasting into Excel. If Zeros is set to hide, zero values will not be copied to the clipboard.
	Unmapped Mass	Copy unmapped stream contents to clipboard, mass basis, for pasting into Excel. If Zeros is set to hide, zero values will not be copied to the clipboard. Unmapped species are those which will not be mapped to the exiting SysCAD stream.
	Unmapped Mole	Copy unmapped stream contents to clipboard, mole basis, for pasting into Excel. If Zeros is set to hide, zero values will not be copied to the clipboard. Unmapped species are those which will not be mapped to the exiting SysCAD stream.
(The following tables display the mass/moles, mass/mole fraction of the individual species.) (Each table (one for each phase) has the following columns (one row for each species):)
Mass / M	Display	Visible when StreamView = Mass. The mass of the species in the product stream.
MassFrac / Mf	Display	Visible when StreamView = Mass. The mass fraction of the species in the product stream.
PhaseMassFrac / IPh:Mf	Display	Visible when StreamView = Mass. The mass fraction of the species in the displayed phase.
Moles / Ml	Display	Visible when StreamView = Mole. The moles of the species in the product stream.
MoleFrac / Mlf	Display	Visible when StreamView = Mole. The mole fraction of the species in the product stream.
PhaseMoleFrac / IPh:Mlf	Display	Visible when StreamView = Mole. The mole fraction of the species in the displayed phase.
ActivityCoeff	Display	Only shown for liquid/aqueous species. The activity coefficient of the species.
SatIdx	Display	Only shown for solid species. The saturation index of the species.
SatIdx.Eff	Display	Only shown for solid species.
Fugacity	Display	Only shown for gaseous species. The fugacity of the species.
Fugacity.Eff	Display	Only shown for gaseous species.

Diff tab page

This tab is only visible if ShowRxnDiff is ticked. The displayed results are the difference between input and output contents.

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
Content Properties Summary
Diff...
Temperature / T	Display	The Temperature difference between the feed and product solutions.
Pressure / P	Display	The Pressure difference between the feed and product solutions.
Mass / M	Display	The Mass difference between the feed and product solutions.
Hf@T	Display	The Enthalpy difference between the feed and product solutions per unit mass. This is calculated by PHREEQC.
Enthalpy / totHf@T	Display	The Enthalpy difference between the feed and product solutions. This is calculated by PHREEQC.
Diff...
SpeciesName		The Species:Long or Short button is used to change the display of the Species names between the Short form, the Chemical compound, or the longer species names.
Zeros		If the Hide Zeros button is clicked, all species that have NO mass flow will be hidden. If the Show Zeros button is clicked, all species will be displayed, including those with zero mass flow.
StreamView		If the Mass button is clicked, the species will be shown in mass flow view. If the Mole button is clicked, the species will be shown in mole flow view.
Stream	Mass	Copy stream contents to clipboard, mass basis, for pasting into Excel. If Zeros is set to hide, zero values will not be copied to the clipboard.
	Mole	Copy stream contents to clipboard, mole basis, for pasting into Excel. If Zeros is set to hide, zero values will not be copied to the clipboard.
	Unmapped Mass	Copy unmapped stream contents to clipboard, mass basis, for pasting into Excel. If Zeros is set to hide, zero values will not be copied to the clipboard. Unmapped species are those which will not be mapped to the exiting SysCAD stream.
	Unmapped Mole	Copy unmapped stream contents to clipboard, mole basis, for pasting into Excel. If Zeros is set to hide, zero values will not be copied to the clipboard. Unmapped species are those which will not be mapped to the exiting SysCAD stream.
(The following tables display the mass/moles, mass/mole fraction of the individual species.) (Each table (one for each phase) has the following columns (one row for each species):)
Mass / M	Display	Visible when StreamView = Mass. The difference in mass of the species.
MassFrac / Mf	Display	Visible when StreamView = Mass. The difference in mass fraction of the species.
PhaseMassFrac / IPh:Mf	Display	Visible when StreamView = Mass. The difference in mass fraction of the species in the displayed phase.
Moles / Ml	Display	Visible when StreamView = Mole. The difference in moles of the species.
MoleFrac / Mlf	Display	Visible when StreamView = Mole. The difference in mole fraction of the species.
PhaseMoleFrac / IPh:Mlf	Display	Visible when StreamView = Mole. The difference in mole fraction of the species in the displayed phase.

Scaling tab page

This tab is only visible if ShowScaling is ticked. This page lists all the Saturation Index for all the solid species in the product.

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
Scaling ...
SpeciesName		The Species:Long or Short button is used to change the display of the Species names between the Short form, the Chemical compound, or the longer species names.
Zeros		If the Hide Zeros button is clicked, all species that have NO mass flow will be hidden. If the Show Zeros button is clicked, all species will be displayed, including those with zero mass flow.
Stream		Copy list of solids species and their Saturation Index to the clipboard, for pasting into external programs such as Excel.
Filter View
Filter		This button will enable or disable the species filter options.
Phases (Only visible if Filter is enabled)	Display	Always set to 'Solids'.
Filters (Only visible if Filter is enabled)	Display	Always set to 'Content'.
Content (Only visible if Filter is enabled)	All	No filtering of species based on element or name.
	Contains Any Element	This will display all species that contain any of the elements entered in their elemental definition.
	Contains All Elements	This will display only species that contain ALL of the elements entered in their elemental definition.
	Starts with ...	This will display species that start with the text entered based on the short or long species tag depending on the current SpeciesTag selection.
	Contains any ...	This will display species that contain the text entered in the currently displayed short or long species tag.
	Contains All ...	This will display species that contain ALL the separate text entered in the currently displayed short or long species tag.
Select	Input	Only visible if Content is NOT set to All. The user specified Elements or text to filter the species list. Refer to Species Filter for more information and examples.
(The following table displays the solid* PHREEQC species from the selected database. The table has the following columns (one row per PHREEQC species.)*
SatIdx	Display	The saturation index of the solid species relative to its equilibrium solubility.
SatIdx.Eff	Display	The saturation index of the solid species adjusted for user specified Saturation Index as defined in the PHREEQC Model Configuration.

Solid.MaxSI	Display	The maximum saturation index of any of the PHREEQC solid species.
Solid.MaxSI_Sp	Display	The PHREEQC solid species which has the maximum saturation index.
Solid.MaxSIEff	Display	The maximum effective saturation index of any of the PHREEQC solid species.
Solid.MaxSIEff_Sp	Display	The PHREEQC solid species which has the maximum effective saturation index.

ElemBal tab page

This tab performs an element balance between the PHREEQC Input and Output streams and separately, between the SysCAD Input and Output streams.

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
ElemBal...
Tol.SigDigits	Input	This provides an easy way to change the Tol.Rel value. For example, 4 here will set Tol.Rel = 1.00e-4. If user changes the Tol.Rel value, this value will also be updated.
Tol.Rel	Input	The relative tolerance for Element Balance (Input - Output). If the relative error is > Tol.Rel then an error is generated. The value of Tol.Rel shown/specified here is used in all PHREEQC unit models which reference the same PHREEQC Model Configuration unit model.
Tol.Abs	Input	The absolute tolerance for Element Balance (Input - Output). If the absolute error is > Tol.Abs then an error is generated. The value of Tol.Abs shown/specified here is used in all PHREEQC unit models which reference the same PHREEQC Model Configuration unit model.
PHREEQC...
ElementBalanceView		If the Mass button is clicked, the elements will be shown in mass flow view. If the Mole button is clicked, the elements will be shown in mole flow view.
Zeros		If the Hide Zeros button is clicked, all elements that have NO mass flow will be hidden. If the Show Zeros button is clicked, all elements will be displayed, including those with zero mass flow.
PHREEQC Element Balance
(The following table displays the mass/molar flows, and absolute and relative errors of the individual elements.) The table has the following columns (one row for each element):
MassIn / M.In	Display	Visible when ElementBalanceView = Mass. The mass of the element in the PHREEQC Input.
MassOut / M.Out	Display	Visible when ElementBalanceView = Mass. The mass of the element in the PHREEQC Output. The QRxnBypass stream is also included in this total. This can be viewed by clickingShowQRxnBypass.
AbsErr / M.Err	Display	Visible when ElementBalanceView = Mass. The difference in mass of the element between the PHREEQC Output and Input.
MolesIn / Ml.In	Display	Visible when ElementBalanceView = Mole. The moles of the element in the PHREEQC Input.
MolesOut / Ml.Out	Display	Visible when ElementBalanceView = Mole. The moles of the element in the PHREEQC Output.
AbsErr / Ml.Err	Display	Visible when ElementBalanceView = Mole. The difference in moles of the element between the PHREEQC Output and Input.
RelErr	Display	The relative difference in amount of the element between the PHREEQC Output and Input, relative to the Input.
Scd...
SysCAD Element Balance
(The following table displays the mass/molar flows, and absolute and relative errors of the individual elements.) The table has the following columns (one row for each element):
MassIn / M.In	Display	Visible when ElementBalanceView = Mass. The mass of the element in the SysCAD Input.
MassOut / M.Out	Display	Visible when ElementBalanceView = Mass. The mass of the element in the SysCAD Output. The QRxnBypass stream is also included in this total. This can be viewed by clickingShowQRxnBypass.
AbsErr / M.Err	Display	Visible when ElementBalanceView = Mass. The difference in mass of the element between the SysCAD Output and Input.
MolesIn / Ml.In	Display	Visible when ElementBalanceView = Mole. The moles of the element in the SysCAD Input.
MolesOut / Ml.Out	Display	Visible when ElementBalanceView = Mole. The moles of the element in the SysCAD Output.
AbsErr / Ml.Err	Display	Visible when ElementBalanceView = Mole. The difference in moles of the element between the SysCAD Output and Input.
RelErr	Display	The relative difference in amount of the element between the SysCAD Output and Input, relative to the Input.

PhDeport tab page

This tab is only visible if PhaseElemDeportment is ticked. This tab shows the mass movement of elements for the Liquid, Solid and Gas phases.

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
PD...
ElementBalanceView		If the Mass button is clicked, the elements will be shown in mass flow view. If the Mole button is clicked, the elements will be shown in mole flow view.
Zeros		If the Hide Zeros button is clicked, all elements that have NO mass flow will be hidden. If the Show Zeros button is clicked, all elements will be displayed, including those with zero mass flow.
PHREEQC.Liquid...
PHREEQC Deportment
(The following table displays the mass/moles, and absolute and relative changes of the individual elements.) The table has the following columns (one row for each element):
MassIn / M.In	Display	Visible when ElementBalanceView = Mass. The mass of the element in the liquid phase of the Input.
MassOut / M.Out	Display	Visible when ElementBalanceView = Mass. The mass of the element in the liquid phase of the Output.
Change / M.Chng	Display	Visible when ElementBalanceView = Mass. The change in mass of the element between the liquid phase of the Output and Input.
MolesIn / Ml.In	Display	Visible when ElementBalanceView = Mole. The moles of the element in the liquid phase of the Input.
MolesOut / Ml.Out	Display	Visible when ElementBalanceView = Mole. The moles of the element in the liquid phase of the Output.
Change / Ml.Chng	Display	Visible when ElementBalanceView = Mole. The difference in moles of the element between the liquid phase of the Output and Input.
RelChange	Display	The relative change in the amount of the element between the liquid phase of the Output and Input, relative to the Input.
PHREEQC.Solid...
PHREEQC Deportment
(The following table displays the mass/moles, and absolute and relative changes of the individual elements.) The table has the following columns (one row for each element):
MassIn / M.In	Display	Visible when ElementBalanceView = Mass. The mass of the element in the solid phase of the Input.
MassOut / M.Out	Display	Visible when ElementBalanceView = Mass. The mass of the element in the solid phase of the Output.
Change / M.Chng	Display	Visible when ElementBalanceView = Mass. The change in mass of the element between the solid phase of the Output and Input.
MolesIn / Ml.In	Display	Visible when ElementBalanceView = Mole. The moles of the element in the solid phase of the Input.
MolesOut / Ml.Out	Display	Visible when ElementBalanceView = Mole. The moles of the element in the solid phase of the Output.
Change / Ml.Chng	Display	Visible when ElementBalanceView = Mole. The difference in moles of the element between the solid phase of the Output and Input.
RelChange	Display	The relative change in the amount of the element between the solid phase of the Output and Input, relative to the Input.
PHREEQC.Gas...
PHREEQC Deportment
(The following table displays the mass/moles, and absolute and relative changes of the individual elements.) The table has the following columns (one row for each element):
MassIn / M.In	Display	Visible when ElementBalanceView = Mass. The mass of the element in the gas phase of the Input.
MassOut / M.Out	Display	Visible when ElementBalanceView = Mass. The mass of the element in the gas phase of the Output.
Change / M.Chng	Display	Visible when ElementBalanceView = Mass. The change in mass of the element between the gas phase of the Output and Input.
MolesIn / Ml.In	Display	Visible when ElementBalanceView = Mole. The moles of the element in the gas phase of the Input.
MolesOut / Ml.Out	Display	Visible when ElementBalanceView = Mole. The moles of the element in the gas phase of the Output.
Change / Ml.Chng	Display	Visible when ElementBalanceView = Mole. The difference in moles of the element between the gas phase of the Output and Input.
RelChange	Display	The relative change in the amount of the element between the gas phase of the Output and Input, relative to the Input.

IPhDeport tab page

This tab is only visible if IPhaseElemDeportment is ticked. This tab shows the mass movement of elements for each PHREEQC phase.

Tag (Long/Short)	Input / Calc	Description/Calculated Variables / Options
IPD...
ElementBalanceView		If the Mass button is clicked, the elements will be shown in mass flow view. If the Mole button is clicked, the elements will be shown in mole flow view.
Zeros		If the Hide Zeros button is clicked, all elements that have NO mass flow will be hidden. If the Show Zeros button is clicked, all elements will be displayed, including those with zero mass flow.
PHREEQC.<PHREEQC PHASE>...
PHREEQC Deportment
(The following table displays the mass/moles, and absolute and relative changes of the individual elements.) The table has the following columns (one row for each element):
MassIn / M.In	Display	Visible when ElementBalanceView = Mass. The mass of the element in the selected PHREEQC phase of the Input.
MassOut / M.Out	Display	Visible when ElementBalanceView = Mass. The mass of the element in the selected PHREEQC phase of the Output.
Change / M.Chng	Display	Visible when ElementBalanceView = Mass. The change in mass of the element between the selected PHREEQC phase of the Output and Input.
MolesIn / Ml.In	Display	Visible when ElementBalanceView = Mole. The moles of the element in the selected PHREEQC phase of the Input.
MolesOut / Ml.Out	Display	Visible when ElementBalanceView = Mole. The moles of the element in the selected PHREEQC phase of the Output.
Change / Ml.Chng	Display	Visible when ElementBalanceView = Mole. The difference in moles of the element between the selected PHREEQC phase of the Output and Input.
RelChange	Display	The relative change in the amount of the element between the selected PHREEQC phase of the Output and Input, relative to the Input.

Preset tab page

The Preset page contains a Copy to Clipboard button which copies the current temperature, pressure and composition of the Preset to the clipboard for pasting into external programs such as Excel.

This page is used to set the required composition of the Pond when it is Preset. This is identical in functionality to the DSp page used in Feeders.

Adding this Model to a Project

Insert into Configuration file

Sort either by DLL or Group.

	DLL:	ScdPHREEQC.dll	→	Units/Links	→	TCE PHREEQC:Dynamic: PHREEQC Pond
or	Group:	Energy Transfer	→	Units/Links	→	TCE PHREEQC:Dynamic: PHREEQC Pond

See Model Selection for more information on adding models to the configuration file.

Insert into Project

Insert Unit

→

TCE PHREEQC

→

Dynamic

→

PHREEQC Pond

See Insert Unit for general information on inserting units.