View source for Multi-Stage Counter Flow Tie

[[Category:Models]]
{{Navigation|[[Models]]|[[Models#Energy Transfer Models|Energy Transfer Models]]}}
{{dryer header table|currentpage=2}}
'''Related Links:''' [[Tie]]

----
{{TOC}}
== General Description ==

This model is designed to emulate equipment that contacts a Gas stream with either a Liquid or Solid stream in counter-current flow.

The Gas enters the at Stage 1 of the unit, while the Liquid (or Solid) stream enters at the Final stage of the unit (if there is only a single stage, then both feeds enter Stage 1).  The user may specify any number of stages from 1 to 5 in the unit.  The Liquids or Solids flow from the Final stage to the Stage 1, while Gas flows in the opposite direction from the Stage 1 to the Final stage.  The user may set a Gas bypass at each stage of the unit and the Gas flow may also have a nominal pressure gradient.

This model can be used to emulate a number of unit operations that involve contacting gas with liquids or solids, including Absorbers, Kilns, Scrubbers, etc.
:[[File:CCTie.png|800px]]

Each stage in the model has an Evaluation Blocks (EB), and hence the user may enable Reactions (RB), Vapour-Liquid Equilibrium (VLE), Solubility (PC) and Environmental Heat Loss (EHX) in each stage. These may be evaluated in any order.

At each stage, the Liquid and Gas streams from previous and succeeding stage are combined and the Evaluation Block is applied to the resulting stream. The contents are then phase split, with the Gas being sent towards the Final stage and the Liquor sent to Stage 1. The evaluations are done '''in parallel''' for a number of iterations. At least as many iterations as there are stages are needed to propagate changes in the feeds to the products.

At each stage entrainment of Solids or Liquids into the Gas, as well as Gas into the Liquor, may be specified. 
:[[File:CCReactor02.png|300px]]

=== Available Sub-Models ===

The following sub-models may be enabled in any, or all, of the stages:
# [[Solubility]] may be enabled in any stage, if this is NOT enabled globally.
# The [[Reaction Block (RB)]] allows the user to configure any number of reactions within a stage.
# The [[Environmental Heat Exchanger (EHX)|Environmental Heat Exchanger Block]] allows the user to add or remove energy from a stage using a number of different methods.
# The [[Vapour Liquid Equilibrium (VLE)|Vapour Liquid Equilibrium Block]] may be enabled in any stage.

=== Diagram ===

:[[Image:Counterflow Tie.png]] OR [[Image:Counterflow Tie2.png]] 

* The diagram shows default drawings of the Multi-Stage Counter Flow Tie with connecting streams.
* The physical location of the streams connecting to the Multi-Stage Counter Flow Tie is unimportant. The user may connect the streams to any position on the unit.
* When inserting a Multi-Stage Counter Flow Tie into a flowsheet, the user may choose a different symbol from the menu.

== Inputs and Outputs ==
 

{| border="1" cellpadding="5" cellspacing="0"  
|- 
| valign="top" rowspan="2" | '''Label''' || valign="top" rowspan="2" | '''Required<br>Optional''' || valign="top" rowspan="2" | '''Input<br>Output ''' ||  colspan="2"   | '''Number of Connections''' || valign="top" rowspan="2" | '''Description'''
|- 
|  '''Min''' || '''Max''' 
|- 
| Liquid Feed || '''Required''' || In || 1 || 10 || Inlet liquid or slurry stream to the Final Stage of the unit.
|- 
| Gas Feed || '''Required''' || In || 1 || 10 || Inlet Gas stream to the Stage 1 of the unit.
|- 
| Liquid Product || '''Required''' || Out || 1 || 1 || Product Liquid or Slurry outlet from the Stage 1 of the unit.
|- 
| Gas Product || '''Required''' || Out || 1 || 1 || Product Gas outlet from the Final Stage of the unit.
|}

== Behaviour when Model is OFF ==

If the user disables the unit, by un-ticking the ''On'' tick box, then the following actions occur:
* All material in streams connected to the Gas Feed inlets will flow straight out of the Gas Product outlet, with no exchange with material entering through the Liquid Feed;
* All material in streams connected to the Liquid Feed inlets will flow straight out of the Liquid Product outlet, with no exchange with material entering through the Gas Feed;
* No sub-models will be called.

So basically, the unit will be 'bypassed' without the user having to change any connections.

== Model Theory ==

In Steady State, all the Gas Feed streams are perfectly mixed, the Bypass stream is removed and the remaining Gas is added to Stage 1.  Similarly, all of the Liquid Feed streams (which may also contain Solids) are perfectly mixed and added to the Final Stage (which may also be Stage 1 if the user has only selected a single stage).

Any sub-models that have been enabled in any of the Stages are carried out on the mixture.

The Liquids and Gases are split after each stage and the Gases are sent to Stage n+1, while the Liquids (and Solids) are sent to Stage n-1.  The Liquid and Gas streams may contain some entrainment of the other phase, if defined by the user.

=== Flow Chart ===

:[[Image:CC Tie Flow Diagram2.png]]

== Data Sections ==

The default access window consists of several sections: 

# '''[[#CFMultiTie|CFMultiTie]]''' - The first tab contains general information relating to the unit and allows the user to set the number of stages, Gas bypass, Entrainment, etc.
# '''[[#EB1|EB1]]''' - This tab allows the user to enable sub-models in the First stage of the unit.  If more than one stage is enabled, then the additional stages will all have a separate page, names EB2, EB3, etc. with the same fields as shown on this page. 
# '''[[Phase Change (PC)|PC1]]''' - Optional tab, only visible if the Solubility is enabled in any of the Evaluation Blocks.  Each stage may have a PC tab page. 
# '''[[RB|RB1]]''' - Optional tab, this tab will be visible for any stages that have Reactions enabled in the Evaluation Block.
# '''[[EHX|EHX1]]''' - Optional tab, this tab will be visible for any stages that have EnvironHX enabled in the Evaluation Block.
# '''[[VLE|VLE1]]''' - Optional tab, this tab will be visible for any stages that have Vapour Liquid Equilibrium (VLE) enabled in the Evaluation Block.
# '''[[Material Flow Section|QGx]]''' - Optional tab, only visible if a Gas flow is enabled in the field ''Stream2View''. This page shows the properties of the selected Gas stream.
# '''[[Material Flow Section|QLx]]''' - Optional tab, only visible if a Liquid flow is enabled in the field ''Stream2View''. This page shows the properties of the selected Liquid/Solid stream.
# '''[[Common Data Sections#Common Data on Info Tab Page|Info]]''' tab - contains general settings for the unit and allows the user to include documentation about the unit and create Hyperlinks to external documents.
# '''[[Links Table|Links]]''' tab, contains a summary table for all the input and output streams. 
# '''[[Audit]]''' tab - contains summary information required for Mass and Energy balance. See [[Model Examples]] for enthalpy calculation Examples.

=== CFMultiTie ===

'''Unit Type: CFMultiTie''' - The first tab page in the access window will have this name.

{|   border="1" cellpadding="5" cellspacing="0" align="center"
|  <div style="text-align: center;">'''Tag (Long/Short)'''</div> || <div style="text-align: center;">'''Input / Calc'''</div> || <div style="text-align: center;">'''Description'''</div>
{{Common Data on First Tab Page}}
|-
|  colspan="3" font style="background: #ebebeb"    | '''''Requirements:'''''
|-
| On || Tickbox || This variable in used to turn the unit ON or OFF. If the unit is OFF, the Gas will flow out of the Gas outlet with no change in state, and the Liquids will flow out of the Liquid outlet with no changes.  So, the phases will not contact each other at all.
|- 
| Stages || List || The user may select between 1 and 5 stages in the unit.
|- 
| Iterations|| Input || Number of internal iterations for solver convergence.
|- 
| Stream2View || List || The user may select to display none or any of the internal Gas or Liquid streams.
|- 
| font style="background: #ebebeb" colspan="3"  | '''''Pressure Control'''''
This allows the user to set if the pressure is fixed or varies across the unit.<br>'''The OperatingP - Method is used as the Reference Pressure, except where StagePressure = ''Linear (calc dP)'' or ''Individual''.'''
|- 
| valign="top" rowspan="6" | StagePressure || Fixed (Gas Feed Reference) || In this case there is no pressure drop across the unit and the Liquid and Gas exit the unit with the same pressure as the pressure in the First Stage (the Gas Feed stage) of the unit. (This pressure is set in the field ''OperatingP - Method'')
|-
| Fixed (Liquid Feed Reference) || In this case there is no pressure drop across the unit and the Liquid and Gas exit the unit with the same pressure as the pressure in the Final Stage (the Liquid Feed stage) of the unit. (This pressure is set in the field ''OperatingP - Method'')
|-
| Linear (Calc dP) || In this case the unit calculates the Total pressure drop across the unit based on the Gas and Liquid Feed pressures.  The Total pressure drop is then divided evenly across all of the stages.
|-
| Linear (User dP Gas Feed Ref) || In this case, the First Stage (the Gas feed stage) is taken as the reference pressure and the user specifies the pressure drop across each stage of the unit.  So, the pressure in the Final stage (the Gas exit stage) will be calculated.
|-
| Linear (User dP Liquid Feed Ref) || In this case, the Final Stage (the Liquid feed stage) is taken as the reference pressure and the user specifies the pressure drop across each stage of the unit.  So, the pressure in the First stage (the Gas entry stage) will be calculated.
|-
| Individual || The user may specify the pressure in each individual stage.
|-
| StageDP_Reqd || Input || This field is only visible if StagePressure  = '''Linear (User dP Gas Feed Ref)''' or '''Linear (User dP Liquid Feed Ref)'''. The user sets the pressure drop that will be applied across each stage in the unit.
|- 
| font style="background: #ebebeb" colspan="3"  | NOTES on OperatingP section:
* If StagePressure  = '''Fixed''' then the entire unit operates at the pressure set by ''Method''.
* If StagePressure  = '''Linear with User dP''', then the user sets the operating pressure in either the First or Last stage of the unit, depending on which option is chosen.  The pressure then changes across the stages according the user defined pressure drop.
* If StagePressure  = '''Linear (calc dP)''' or '''Individual''' then this section is not visible.
{{OperatingP}}
|-
| StageDP || font style="background: #ebebeb" | Display || The calculated pressure drop across each stage in the unit. This field is not visible if StagePressure  = '''Individual'''.
|-
|  colspan="3" font style="background: #ebebeb"    | '''''Stage Requirements'''''
The table shown here allows the user to set the Gas bypass and the entrainment values.  The user may set a single value that is applied to each stage by ticking the 'All' box and then setting the required value in the first column.  Otherwise, do not tick the 'ALL' box and set the values individually for each stage.
|-
|PressureReqd || Input  || This is only visible if StagePressure  = '''Individual'''.  This allows the user to set the pressure individually for each stage, or in the entire unit if the 'All' tickbox is enabled.
|-
|GasBypass || Input  || This allows the user to set the Gas bypass, as a single value applied to each stage (All = ticked), or individually for each stage (All = unticked).
|-
|  colspan="3" font style="background: #ebebeb"    | '''''Entrainment'''''
|-
| VapToLiqStream/VapToLiq || Input || This allows the user to set the Vapour entrainment in the Liquid stream, as a single value applied to each stage, or individually for each stage.
|-
| SolToGasStream/SolToGas || Input || This allows the user to set the Solid to Gas entrainment, as a single value applied to each stage, or individually for each stage.
|-
| LiqToGasStream/LiqToGas || Input || This allows the user to set the Liquid to Gas entrainment, as a single value applied to each stage, or individually for each stage.
|-
|  colspan="3" font style="background: #ebebeb"    | '''''Stage Results Summary'''''
The table shown here gives a summary of the conditions in each of the individual stages.
|-
|Pressure/P || font style="background: #ebebeb" | Display || The exit pressure from each individual stage.
|-
|VapMassFlow/VQm || font style="background: #ebebeb" | Display || The Gas flow from each individual stage.
|-
|LiqMassFlow/LQm || font style="background: #ebebeb" | Display || The Liquid flow from each individual stage.
|-
|SolMassFlow/SQm || font style="background: #ebebeb" | Display || The Solids flow from each individual stage.
|-
|TempIn/Ti || font style="background: #ebebeb" | Display || The Temperature into each individual stage (after the Gas and Liquid/Solid steams are combined, but before any sub-models are evaluated.)
|-
|TempOut/To || font style="background: #ebebeb" | Display || The Temperature out of each individual stage.
|-
|  colspan="3" font style="background: #ebebeb"    | '''''Stream Summary'''''
The table shown here gives a summary of variables in each of the internal Gas (from GasFeed to GasProd) and Liquid/Solid (from LiqFeed to LiqProd) streams between the stages.  
|-
|MassFlow/Qm || font style="background: #ebebeb" | Display || The mass flow in the individual internal streams.
|-
|VapourFrac/Vf || font style="background: #ebebeb" | Display || The Vapour fraction in the individual internal streams.
|-
|Temperature/T || font style="background: #ebebeb" | Display || The Temperature of the individual internal streams.
|}

=== EBs ===

Each Stage has its own EB section. The user may enable the required sub-models in each stage.

{|   border="1" cellpadding="5" cellspacing="0" 
|width=150|'''Tag (Long/Short)'''||'''Input / Calc'''||'''Description/Calculated Variables / Options'''
|-
|  colspan="3" font style="background: #ebebeb"    | '''Stage X Evaluation Block'''
{{EB Evaluation Data Section | Reactions = Yes | EnvironHX = Yes | VLE = Yes }}
|}

== Adding this Model to a Project ==

{{Adding Model to a Project | DllName=Basic2 | DllSubGroup=Process | UnitOp=Tie - Multistage Counter Flow | Group=Energy Transfer}}

== Hints and Comments ==

# There may be mass entering or leaving the unit via the [[Reaction Block (RB)|Reaction Block]] source or sink, so if the outgoing mass is not the same as the incoming mass, this may be a place to check first.

== Example Project == 

*[[Nickel Copper Project]] - flowsheet 6.
*[[Example_30_Lithium#Demo_Lithium_Carbonate_CRM_Project|Demo Lithium Carbonate CRM Project]] - flowsheet 1.